1、Ord No:M571Mold No.:*Part No.:37-05385/37-05387Part name:BASE PER EROGATORE VASCHETTA EROGATORE Date:29-Jul,2016index Mold basic information 1.Mold structure:1.1 Parting line;1.2 Gate type/position;1.3 Ejection type/position;1.4 Mold layout;2.Part analysis:2.1 Draft angle analysis(green without draf
2、t angle);2.2 Thickness analysis;3.Suggestion for part:Part data-37-05385part nameBASE PER EROGATOREpart size(mm)L:71mm W:70.2mmH:20.6mm weight(g)10 gr surface finishCavity:diamond polishCore:#320 sand papermaterialABS SINKRALL C442shrink.rate0.55%Part data-37-05387part nameVASCHETTA EROGATOREpart si
3、ze(mm)L:56mmW:54mmH:2mmweight(g)39grsurface finishCavity:#600 sand paperCore:#320 sand papermaterialABS SINKRALL C442shrink.rate0.55%Mold dataMould No.GDM1654Mold steelCavity:1.2083 HRC 50-52Core:1.2083 HRC 50-52Slide:1.2083 HRC 50-52mold base:S50CMold part standardEquivalent HASCONumber of Cavities
4、1+1Gate typeCold runner+sub gateEjection typeEjector pinCooling byWater 1.11 Parting line CavityPLCore 1.12 Parting line CavityPLCore 1.13 Parting line-insertCavity side(red line)Core side(red line)1.14 Parting line-insertCore side(red line)Cavity side(red line)slide side(red line)slide slide 1.15 P
5、arting line-slide 1.2 Gate injection positionCold runner+sub gateCold runner+sub gate1.3 Ejection type positionEjector pinstraight ejector blockTOP 1.4 Mold layout slide slide 2.1 Draft angle analysis2.11 Draft angle analysis2.2 Thickness analysis2.21 Thickness analysis3.11 Suggestion for partNo dra
6、ft angle for green surface,suggest to add 1 degree by cut material,please confirm!we will add 1degree draft angle.3.12 Suggestion for partNo draft angle for green surface,suggest to add 1 degree by cut material,please confirm!we will add 0.5degree draft angle.3.13 Suggestion for partIn order to make
7、 parting line simple,suggest change draft angle to core side from cavity by cut some material as red line,please confirm!we will modify the part.3.14 Suggestion for part1.00MM1.10MM In order to avoid sink mark,suggest to make all ribs same as right view,please confirm!we will modify the part(cut mat
8、erial on inner side).In order to avoid thin steel,suggest to cut some rib as line area(both side),Please confirm!3.15 Suggestion for part0.8mmwe will modify the part.3.16 Suggestion for partIn order to increase the wall thickness for ejector sleeve,please keep the size for“W”to 1mm,suggest reduce th
9、e angle for blue surface,cancel the radius as red surface,increase the wall thickness for the boss,please confirm!AAAAAAAAAASECTION A-AW3.17 Suggestion for partThere are under cut on blue surface,suggest remove the radius,please confirm!3.18 Suggestion for partThere are under cut on blue surface,sug
10、gest change the draft angle to solve it,please confirm!3.19 Suggestion for partThere are under cut on red line area,suggest change the draft angle to solve it by cut material(both side),please confirm!3.20 Suggestion for partIn order to get better mold life,suggest increase the draft angle to 2degree from 0.5 degree,please confirm!
